基于灰色关联度的微孔端面机械密封开启力共性影响参数分析

目前微孔端面机械密封采用的几何参数繁多,缺乏明确物理意义。为找出跨孔型的共性几何参数,基于Fluent多相流空化模型,针对矩形孔、菱形孔、椭圆孔端面机械密封,建立密封间隙流体的三维数值计算模型,计算得到144条开启力数据;在分析开启力和几何尺寸之间的关系、额外开启力产生机制的基础上,提出等效长度和等效宽度2个具有物理意义的几何参数;采用灰色关联度分析法,分析和验证等效长度、等效宽度、方向角、面积比对开启力的影响,发现4个因素对3种微孔密封的间隙流体开启力都有影响,但等效长度与等效宽度的影响较方向角、面积比大。     

Effect of the doping time of the 1‐butyl‐3‐methylimidazolium ionic liquid cation on the Nafion membrane proprieties

Nafion membranes were prepared by incorporating in the polymer matrix the 1‐butyl‐3‐methylimidazolium (BMI⁺) ionic liquid cation at different doping levels. Increasing the doping time of the membranes with the ionic liquid results in increased incorporation of the BMI⁺ cation but a decrease in the bulk conductivity. The thermogravimetric analysis shows that the BMI⁺ cation incorporation increases the thermal stability of the membranes. The higher discharge efficiency of the fuel cell at 80°C was obtained by using Nafion membrane after 15 minutes of doping in the ionic liquid solution.     

Exergy analysis of the diesel pre-reforming solid oxide fuel cell system with anode off-gas recycling in the SchIBZ project. Part I: Modeling and validation

Solid oxide fuel cell (SOFC) systems with anode off-gas recirculation (AGR) and diesel pre-reforming are advantageous because they can operate with the current fuel infrastructure. In the SchIBZ-project, the prototype of such a SOFC system for maritime applications has already been commissioned. In this first paper, we model the system devices to conduct an exergy analysis of this real SOFC plant and validate them with experimental values from experiments in laboratory scale. The results of our simulation agree well with the experimental values. The calculations with the validated results may be closer to the real thermodynamic behavior of such system components than previous literature.     

内插螺旋立式上行管流场及传热性能的实验研究

通过粒子图像测速流场实验与传热实验相结合，研究了内插螺旋立式上行管的螺旋节距、丝径、中径比等结构参数在不同Re下对流场、阻力及传热性能的影响。结果表明，内插螺旋能够有效扰动和混合管内流体，使管内形成多个纵向旋涡的流体结构、增大管壁附近液体涡量，有利于强化传热。当Re相同时，管内平均流速v、Nu和综合换热性能PEC均随丝径增大而增大，随中径比减小而增大；随节距增大，3种参数均出现增大的趋势，节距大于20 mm后开始减小。管内流体的阻力f随丝径和节距增大而减小，随中径比增大而增大。综合比较，在较低Re时，节距p=20 mm、丝径e=1.6 mm、中径比D/d=0.75时综合传热效果最好。     

介孔分子硅剂改善茶浓缩膜结构特性应用研究

为有效提高功能性茶浓缩反渗透膜的回收效率和抗污性能,探究了3种介孔分子硅材料(MCM-41、SBA-15和MCFs)对浓缩膜面聚酰胺层聚合形成过程的结构影响。结果表明,添加质量分数0.02%经磺化预处理的MCM-41于间苯二胺水相可接枝酰氯基团,形成的聚酰胺结构层峰谷粗糙跨度仅为220 nm且交联紧致,膜抗拉伸强度增加37.8%;SBA-15和MCFs相膜面峰谷跨度达500~780 nm,横向褶皱和团聚,结构存在孔道塌陷;改性膜在3 h内对茶多酚、茶多糖、茶蛋白即可达到最大浓缩度,减少50%浓缩时间;MCM-41和SBA-15膜长时间运行的浓缩降率仅为2.8%~6.1%,48 h下降率比显示改性膜达标使用时长增加112.5%~137.5%,亲水性和抗污堵能力均大幅提升,可有效满足功能化茶浓缩精度。     

微观表面形貌对螺旋槽液膜密封空化发生的影响

为探索微观表面形貌对液膜密封空化的影响,基于满足质量守恒的JFO空化模型及坐标变换,建立考虑微观表面形貌的双坝区螺旋槽液膜密封数学模型;采用有限体积法离散求解控制方程,综合分析表面粗糙度、周向波度和径向锥度对螺旋槽液膜密封空化发生的影响规律。结果表明:相比而言,密封面计入微观表面形貌后,摩擦副液膜中空穴区发生位置分散且形状不规则;以空化面积比为判据,较大表面粗糙度对液膜空化促生虽起到积极作用,但数据较小,可忽略不计;锥度对液膜中空穴促生和抑制影响有限,波幅的增加显著促进液膜中空穴的发生;高频波数时,正锥度有利于降低液膜空化面积比,抑制空穴。     

Automatic Transformation of Membrane‐Type Electronic Devices into Complex 3D Structures via Extrusion Shear Printing and Thermal Relaxation of Acrylonitrile–Butadiene–Styrene Frameworks

This work demonstrates a means of automatic transformation from planar electronic devices to desirable 3D forms. The method uses a spatially designed thermoplastic framework created via extrusion shear printing of acrylonitrile–butadiene–styrene (ABS) on a stress‐free ABS film, which can be laminated to a membrane‐type electronic device layer. Thermal annealing above the glass transition temperature allows stress relaxation in the printed polymer chains, resulting in an overall shape transformation of the framework. In addition, the significant reduction in the Young's modulus and the ability of the polymer chains to reflow in the rubbery state release the stress concentration in the electronic device layer, which can be positioned outside the neutral mechanical plane. Electrical analyses and mechanical simulations of a membrane‐type Au electrode and indium gallium zinc oxide transistor arrays before and after transformation confirm the versatility of this method for developing 3D electronic devices based on planar forms.     

水射流表面改性对国产Zirlo锆合金包壳管加速腐蚀氧化膜形貌的影响

为进一步提高国产锆合金包壳管性能,提高反应堆安全性,对国产Zirlo锆合金进行水射流冲击强化,研究在高温高压水腐蚀条件下不同冲击压力对样品表面氧化膜的影响,并与未冲击样品进行对比。结果表明,样品表面在不同压力的冲击下耐蚀性差异较大,当冲击压力达到40 MPa时样品表面氧化膜状态较好,相比于未冲击样品氧化膜厚度减少4.3%,在10 MPa和20 MPa冲击下则出现腐蚀加速情况。